The Graco 695 sprayer is a trusted and durable paint spraying machine. When using the right accessories, you can make your paint spraying experience easier, faster, and more efficient with the use of a few parts.

Parts of the Graco Paint Sprayer

The 695 graco paint sprayer parts: the pump, the hose, and the gun.

The pump is responsible for drawing paint from the container and delivering it to the hose. The hose then carries the paint to the gun. The gun can use to apply the paint to the surface.

How to Assemble the Graco Paint Sprayer?

·        Begin by attaching the paint bucket to the paint sprayer. Attach the hose to the paint sprayer. Make sure that the hose is securely attached.

·        Next, insert the tip into the paint sprayer. Make sure that the tip is inserted correctly and that it is tight.

·        Finally, turn on the paint sprayer and begin painting. Make sure to keep the paint sprayer moving so that the paint does not dry in one spot.

How to Fill a Graco Paint Sprayer?

To fill a Graco paint sprayer, first remove the cap from the paint container and pour the paint into the reservoir. Next, screw the pump assembly onto the container. Then, turn on the power switch and press the prime button to start the pump.

How to Remove the Graco Paint Sprayer Cap, Spray Gun, and Air Filter Assembly?

To remove the Graco paint sprayer cap, spray gun, and air filter assembly, first disconnects the power supply. Then, unscrew the cap from the spray gun. Next, remove the air filter by pulling it out of the housing. Finally, unscrew the spray gun from the air hose.

Now that you have removed all of the 695 graco paint sprayer parts. You can clean them according to the instructions in your Graco paint sprayer manual. Be sure to put all of the parts back in their proper place before you start painting again.

Assembling the Vacuum System on a Graco Paint Sprayer

·       Begin by attaching the suction hose to the inlet port on the pump.

·       Next, connect the discharge hose to the outlet port on the pump.

·       Finally, connect the power cord to the pump and plug it into a power outlet.

·       Once the vacuum system assembles, turn on the pump and let it run for a few minutes to build up pressure.

·       Then, hold the tip of the spray gun about six inches from the surface you want to paint and pull the trigger.

·       Move the spray gun in a back-and-forth motion as you paint.

·       When you're finished painting, turn off the pump and disconnect all of the hoses and cords.

Cleaning and Disassembling a Graco Paint Sprayer

To clean a Graco paint sprayer, first disassemble the unit by removing the paint cup, spray tip, and hose. Next, rinse the paint cup and spray tip with clean water. Then, use a brush to remove any remaining paint from the cup and tip. Finally, rinse the inside of the paint sprayer with clean water.

To disassemble a Graco paint sprayer, first remove the paint cup, spray tip, and hose. Next, unscrew the cap from the top of the unit and remove the inner sleeve. Finally, remove the O-ring from the bottom of the unit.

Graco 695 manifold filter

The 695 graco paint sprayer parts manifold filter is an important part of your paint sprayer. It helps to ensure that the paint is evenly distributed and that there are no clumps.

To use the Graco 695 manifold filter, first remove the filter from the package. Next, place it in the paint cup and screw it into place. Finally, tighten the knob until it is snug.

Be sure to check the filter regularly and replace it when it becomes clogged. This will help to keep your paint sprayer working properly and prevent any issues with painting.

Graco 695 pump replacement

You will need to remove the old pump from your Graco paint sprayer before you can install the new one. To do this, first disconnect the power supply from the machine. Then, locate the two bolts that hold the pump in place. Use a wrench to loosen these bolts, and then carefully remove the old pump.

Next, take the new pump and connect it to the power supply. Once it's connected, tighten the two bolts to secure it in place. Once the new pump install, you can now re-connect the power supply and turn on your paint sprayer. You will want to run the paint sprayer for several minutes with water to ensure the pump is working properly. If there are no leaks, you are now ready to use this machine again.

695 Graco paint sprayer parts for a variety of tasks around your house. From painting walls and ceilings to filling in cracks and holes, these sprayers will have your projects completed quickly and easily.